We maintain deep inventories of stainless steel fittings to provide quick shipments. These disadvantages are less problematic for fire sprinkler installations, because standing water in the steel pipes does not flow, except during occasional tests or actual activation by a fire. The introduction of oxygen dissolved in fresh supplies of water will cause some corrosion, but this soon stops in the absence of any source of further water-borne oxygen. Threaded steel pipe is widely used in buildings to convey natural gas or propane fuel, and is also a popular choice in fire sprinkler systems due to its resistance to mechanical damage and high heat .
If the 3 sides of T-fitting are similar in size then it is called as Equal tee otherwise it is called as Unequal tee. The advantages of this method are durability, speed, neatness, and safety. Some crimped fittings are designed to be used with copper tubing, without requiring flux or filler metal. Although crimped fittings are suitable for drinking-water pipes and other hot-and-cold systems , they are substantially more expensive than sweated fittings. Where many connections must be made in a short period of time , soldering is quicker and less expensive joinery than compression or flare fittings.
The radius of curvature of a long-radius elbow is 1.5 times the pipe diameter, but a short-radius elbow has a radius equal to the pipe diameter. Short elbows, widely available, are typically used in pressurized systems, and in physically tight locations. 90 Degree elbow is installed between the pipe to change the direction of the pipe by 90 Degree.
The cones of the assembly studs are subject to normal wear and must be checked at regular intervals with taper gauges. Each screw sleeve must be used only once for finishing assembly on the pipe; using the same sleeve again may impair its function. This instruction describes the pre-assembly of a cutting ring on the pipe in a pipe screw sleeve or assembly stud. The surfaces of steel fitting bodies, union nuts and cutting rings are protected from corrosion as standard with a CrVI-free zinc-nickel coating conforming to DIN EN 15205.
The larger-diameter hub was also called a “bell” because of its shape. Adequate ventilation is essential to remove metal fumes from welding operations, and personal protective equipment must be worn. Because the high temperatures during welding can often generate intense ultraviolet light, dark goggles or full face shields must be used to protect the eyes.
Our range of pipe tools also includes press fit tools to help with quick jobs on site. These fittings are used for small bore and low-pressure piping. 2000 class fittings are available in only in threaded type. Reducing coupling is used to connect two different sizes of pipe.
Lightly oil the cone of the screw sleeve and the thread of the union nut. With sealing cone screw-on fittings with O-ring (AOL / AOS), the pre-stressing of the O-ring must be bridged and the sealing cone must lie metallically flush against the cone of the HL/HS connector. At this point, the cutting ring may be allowed to rotate, but must not move axially. Tightening torques for stainless steel fittings and for fittings with UN/UNF threads available upon request. The entire fitting consists of the threaded connector, the spacer ring with O-ring seal, the pressure ring and the union nut.
Our goal is to help make purchasing quick with fewer shipping costs and less time spent scouring the web for the pipe fittings you need. Tee type fitting is a component of plumbing system which is in T-shape. It is having one inlet and two outlets, outlets are arranged at 90o to the main line connection . It can also be used to combine the flow from two inlets to one outlet. They are also available in different materials and different sizes.
An advantage of this type of fitting is that the pipe it is connecting to does not need to be cut to a precise length; the slip joint can attach within a range of the end of the inserting pipe. Many slip fittings may be tightened or loosened by hand, for easier access to residential drainpipe systems . Because they operate at low pressure and rely on gravity to move fluids , drain-waste-vent systems use fittings whose interior surfaces are as smooth as possible. Freshly cut ends of pipe segments are carefully deburred to remove projecting slivers of material which may snag debris which can build up to cause blockages. This internal smoothness also makes it easier to “snake out” or “rod out” a clogged pipe with a plumber’s snake. An elbow is installed between two lengths of pipe to allow a change of direction, usually a 90° or 45° angle; 22.5° elbows are also available.
